Zum Wireless Wall-box Dimmer, Gray Smooth

A wireless wall-box dimmer for 0-10 Volt load control of LED drivers in a Zum™ commercial lighting system.

The Zum™ wireless wall-box dimmer (ZUMMESH-5A-LV) provides control of a single 5 Amp, 100-277 Volt lighting load of 0-10 Volt dimmable LED drivers or fluorescent ballasts. It features a single rocker switch to enable simple on/off switching and dimming adjustment, with the ability to save one preset. Standard gang-box installation allows one or more units to be installed in a 3-1/2 inch (89 mm) deep electrical box (decorator-style faceplate sold separately).

Built-in Zum Mesh wireless technology affords easy “pair and play” integration as part of a complete Zum commercial room lighting system. Energy-saving options are available to enable daylighting, occupancy or vacancy sensing, and centralized monitoring and management.

Pair and Play

Designed with flexibility and ease-of-use in mind, Zum dimmers are pre-programmed with “pair and play” functionality. An installer can simply install the dimmer in a room along with Zum occupancy or vacancy sensors and/or a daylight sensor, set up the room with a few quick button taps, and then use the dimmer to control the lights in the room – no programming required! Room setup can also be accomplished using the Zum app if the room is equipped with a Zum Network Bridge. The Zum Network Bridge also enables centralize monitoring and management via a Zum Floor Hub and Zum Wireless Gateway.

Zum Mesh Wireless Technology

Ultra-reliable Zum Mesh wireless technology provides steadfast peer-to-peer RF communications within a commercial space without the need for physical control wiring, hubs, or gateways. Employing a Wi-Fi® friendly 2.4GHz peer-to-peer mesh network topology, nearly every Zum Mesh device acts as an “expander,” relaying wireless commands directly between Zum Mesh devices to ensure that every command reaches its intended destination without disruption.

• Spec Sheet available - Yes

• Operating Temperature (Maximum): 104 F
• Operating Temperature (Minimum): 32 F
• Certifications: UL, FCC
• AC Voltage (Maximum): 277 Volts
• AC Voltage (Minimum): 120 Volts
• Active Power: 1 Watt
• Current Draw: 5 Amps
• Depth: 1.80 in
• Height: 4.13 in
• Width: 1.75 in
• Product Weight: 0.31 lbs
• Color: Gray
• Load Ratings:
  •Dim Load Types: 0-10 Volt LED driver or fluorescent ballast (4-wire), 60 mA maximum current sink
  •Dim Control Output: 0-10 Volts DC, 60 mA sink or source
• Wireless Communications:
  •RF Transceiver: 2-way RF, 2.4GHz ISM Channels 15, 20, 25, or 26 (channel auto-selected), IEEE 802.15.4 compliant
  •Zum Mesh Range (Typical): 50ft (15m) indoor to nearest peer-to-peer mesh network devices
  •Subject to site-specific conditions and individual device capabilities
  •Note: A maximum of 32 Zum Mesh wireless devices is permitted per room
• Controls and Indicators:
  •Switch: (1) 3-Position rocker switch (spring return to center); press up to recall the locally saved preset (turns the lighting load on at the saved preset dim level), press down to turn the lighting load off, press and hold up or down to raise or lower the dimming level; also used for creating a preset, room setup, and factory reset
  •Status: (1) Green LED, indicates the lighting load is turned on; also used for creating a preset, room setup, and factory reset
• Connections:
  •Hot: (1) 16 AWG Class 1 flying lead, black, line power input
  •Neutral: (1) 16 AWG Class 1 flying leads, white, neutral
  •Ground: (1) 16 AWG Class 1 flying lead, green, ground
  •Switched Load: (1) 16 AWG Class 1 flying lead, red, switched load output
  •0-10V Dim +: (1) 18 AWG Class 1 flying lead, purple, 0-10 Volt DC dimming control output, positive
  •0-10V Dim –: (1) 18 AWG Class 1 flying lead, gray, 0-10 Volt DC dimming control output, negative
• Construction:
  •Composition: Plastic housing and front face with metal bracket
  •Mounting: Mounts in a 1-gang (or larger) 3-1/2 inch (89mm) deep electrical box (not included)
  •Faceplate: Requires a decorator-style faceplate